Keysight1200X

class Keysight1200X(

visa_resource: str | VisaConfig,

)

Bases: ScopeDriverBase

SCPI driver for Keysight InfiniiVision 1200 X-Series oscilloscopes.

Methods

check_errors	Query :SYSTem:ERRor? once and raise on a non-zero code.
close	Close the underlying transport.
digitize	:DIGitize the cached trigger source, then *OPC? under a scoped VISA timeout.
fetch_waveform	Fetch the waveform from channel over WORD (unsigned 16-bit, LSB-first), 1000 points.
force_trigger	Force a trigger event immediately, regardless of the configured conditions.
get_acquisition_mode	Read back the current acquisition mode.
get_acquisition_state	:OPERegister:CONDition? bit 3 (0x08) — set = RUNNING, clear = STOPPED.
get_average_count	Read back the waveforms-to-average count.
get_coupling	Read back input coupling on channel.
get_horizontal_scale	Read back the timebase (seconds/div).
get_probe_attenuation	Read back channel's probe attenuation ratio.
get_sample_rate	Read back the current sample rate (samples per second).
get_trigger_status	:OPERegister:CONDition? bits: 0x20 = ARMED, 0x08 = AUTO (running), else TRIGGERED.
get_vertical_offset	Read back channel's vertical offset (volts).
get_vertical_scale	Read back channel's vertical scale (V/div).
load_settings	:RECall:SETup from scope memory, or send local bytes via :SYSTem:SETup.
measure	Install then query a built-in measurement on channel.
open	Open the underlying transport.
run	Start continuous (free-running) acquisition.
save_screenshot	:SAVE:IMAGe to the scope, or :DISPlay:DATA? PNG,COLor and write locally.
save_settings	:SAVE:SETup to scope memory or to the host (:SYSTem:SETup?).
set_acquisition_mode	Set the acquisition mode.
set_average_count	Set the number of waveforms to average.
set_coupling	Set AC/DC input coupling on channel.
set_horizontal_scale	Set the timebase to seconds_per_div.
set_probe_attenuation	Set channel's probe attenuation ratio (e.g. 1, 10, 100, 1000).
set_trigger_level	Set the trigger threshold to level (volts).
set_trigger_mode	Set the trigger sweep mode (AUTO / NORMAL).
set_trigger_slope	Set the trigger edge slope (RISING / FALLING / EITHER).
set_trigger_source	Set the trigger source to analog channel.
set_trigger_type	Set the trigger type (EDGE, PULSE, …).
set_vertical_offset	Set channel's vertical offset to offset (volts).
set_vertical_scale	Set channel's vertical scale to volts_per_div (V/div).
setup_measurement	Ensure a measurement slot exists for measurement_type/channel before the scope triggers.
single	Arm a single-shot acquisition.
stop	Stop acquisition.

open() → None

Open the underlying transport. Idempotent.

Concrete drivers also perform any one-shot instrument setup here (e.g. *CLS, remote-mode handshake).

close() → None

Close the underlying transport. Idempotent.

check_errors() → None

Query :SYSTem:ERRor? once and raise on a non-zero code. Does not drain the queue.

set_vertical_scale(

volts_per_div: float,

channel: int,

) → None

Set channel’s vertical scale to volts_per_div (V/div).

Drivers may snap to the nearest hardware-supported step. Callers that need the actual applied value should get_vertical_scale() afterward.

get_vertical_scale(channel: int) → float

Read back channel’s vertical scale (V/div).

set_vertical_offset(offset: float, channel: int) → None

Set channel’s vertical offset to offset (volts).

get_vertical_offset(channel: int) → float

Read back channel’s vertical offset (volts).

set_coupling(

coupling: Coupling,

channel: int,

) → None

Set AC/DC input coupling on channel.

get_coupling(channel: int) → Coupling

Read back input coupling on channel.

set_probe_attenuation(factor: float, channel: int) → None

Set channel’s probe attenuation ratio (e.g. 1, 10, 100, 1000).

get_probe_attenuation(channel: int) → float

Read back channel’s probe attenuation ratio.

set_horizontal_scale(seconds_per_div: float) → None

Set the timebase to seconds_per_div. Applies globally to all channels.

get_horizontal_scale() → float

Read back the timebase (seconds/div).

get_sample_rate() → float

Read back the current sample rate (samples per second).

This is the effective hardware rate the scope is acquiring at; it depends on the timebase, memory depth, and interpolation settings.

set_acquisition_mode(

mode: AcquisitionMode,

) → None

Set the acquisition mode.

Drivers should raise NotImplementedError for AcquisitionMode values their scope doesn’t support (e.g. Keysight 1200X has no ENVELOPE mode).

get_acquisition_mode() → AcquisitionMode

Read back the current acquisition mode.

set_average_count(count: int) → None

Set the number of waveforms to average. Only takes effect in AcquisitionMode.AVERAGE.

get_average_count() → int

Read back the waveforms-to-average count.

run() → None

Start continuous (free-running) acquisition.

stop() → None

Stop acquisition. Leaves the captured data intact for fetch_waveform / measure.

single() → None

Arm a single-shot acquisition.

Non-blocking — use get_acquisition_state to poll for STOPPED, or prefer digitize() which combines arming and waiting.

digitize(timeout: float) → None

:DIGitize the cached trigger source, then *OPC? under a scoped VISA timeout.

On timeout, clear() aborts the pending op and restores the session.

get_acquisition_state() → AcquisitionState

:OPERegister:CONDition? bit 3 (0x08) — set = RUNNING, clear = STOPPED.

fetch_waveform(

channel: int,

) → WaveformData

Fetch the waveform from channel over WORD (unsigned 16-bit, LSB-first), 1000 points.

measure(

measurement_type: ScopeMeasurementType,

channel: int,

) → float

Install then query a built-in measurement on channel.

The install form runs first as a guard — bad command syntax surfaces via check_errors() before we’d block on the query. The vendor’s invalid-measurement sentinel maps to NaN.

set_trigger_source(channel: int) → None

Set the trigger source to analog channel.

Drivers typically cache this value because the trigger-level SCPI on some scopes requires the source channel in the same command.

set_trigger_type(

trigger_type: TriggerType,

) → None

Set the trigger type (EDGE, PULSE, …).

set_trigger_level(level: float) → None

Set the trigger threshold to level (volts). Applies to the configured trigger source.

set_trigger_slope(

slope: TriggerSlope,

) → None

Set the trigger edge slope (RISING / FALLING / EITHER).

set_trigger_mode(

mode: TriggerMode,

) → None

Set the trigger sweep mode (AUTO / NORMAL).

AUTO forces an acquisition if no trigger fires within the timeout; NORMAL waits indefinitely for a real trigger.

force_trigger() → None

Force a trigger event immediately, regardless of the configured conditions.

get_trigger_status() → TriggerStatus

:OPERegister:CONDition? bits: 0x20 = ARMED, 0x08 = AUTO (running), else TRIGGERED.

save_screenshot(

filepath: str,

to_instrument: bool = False,

) → bytes

:SAVE:IMAGe to the scope, or :DISPlay:DATA? PNG,COLor and write locally.

save_settings(

name: str,

to_instrument: bool = False,

) → bytes

:SAVE:SETup to scope memory or to the host (:SYSTem:SETup?).

load_settings(

name: str,

from_instrument: bool = False,

) → None

:RECall:SETup from scope memory, or send local bytes via :SYSTem:SETup.

setup_measurement(

measurement_type: ScopeMeasurementType,

channel: int,

) → None

Ensure a measurement slot exists for measurement_type/channel before the scope triggers.

Required for instruments (e.g. Tektronix) that compute measurements during acquisition — the slot must be present at trigger time or the first measure() returns stale/invalid data. Default is a no-op for instruments (e.g. Keysight 1200X) that compute on demand.