Keysight33521B

class Keysight33521B(

visa_resource: str | VisaConfig,

)

Bases: AWGDriverBase

SCPI driver for the Keysight 33521B arbitrary waveform generator.

Methods

align_phase	Sync the phase of all channels.
burst_enable	Enable or disable burst mode on the given channel.
close	Close the underlying transport.
fire_burst_trigger	Fire a burst trigger on channel now; the trigger source must already be MANUAL.
fire_sweep_trigger	Fire a sweep trigger on channel now; the trigger source must already be MANUAL.
get_amplitude	Get the current output amplitude and voltage unit on channel.
get_burst_delay	Get the burst trigger delay (seconds) on channel.
get_burst_gate_polarity	Get the gate polarity for GATED bursts on channel.
get_burst_ncycles	Get the number of cycles per trigger for NCYCLE bursts on channel.
get_burst_period	Get the internal burst period (seconds) on channel.
get_burst_state	Return True if burst mode is enabled on channel.
get_burst_trigger	Get the burst trigger source on channel.
get_burst_type	NCYCLE reads back as INFINITE when BURS:NCYC is the hardware's high-water sentinel for INF.
get_modulation_state	Get the modulation enabled state currently active on channel.
get_modulation_type	Returns modulation type currently enabled, or the last type set by the user when modulation is not enabled.
get_offset	Get the DC offset (volts) on channel.
get_output_load	Get the output load impedance; None means high-Z.
get_output_state	Return True if the output on channel is enabled.
get_sweep_end_freq	Get the sweep end frequency (Hz) on channel.
get_sweep_return_time	Get the sweep return time (seconds) on channel.
get_sweep_start_freq	Get the sweep start frequency (Hz) on channel.
get_sweep_start_hold_time	Get the sweep start hold time (seconds) on channel.
get_sweep_state	Return True if sweep mode is enabled on channel.
get_sweep_stop_hold_time	Get the sweep stop hold time (seconds) on channel.
get_sweep_time	Get the sweep time (seconds) on channel.
get_sweep_trigger	Get the sweep trigger source on channel.
get_sweep_type	Get the sweep type currently configured on channel.
get_waveform	Get the current waveform on channel.
modulation_enable	Enables the most recently configured modulation type, or disables modulation.
open	Open the underlying transport.
output_enable	Enable or disable the output on channel.
set_amplitude	Set the output amplitude on channel.
set_burst	Configure channel's burst type.
set_burst_delay	Set the burst trigger delay (seconds) on channel.
set_burst_gate_polarity	Set the gate polarity for GATED bursts on channel.
set_burst_ncycles	Set the number of cycles per trigger for NCYCLE bursts on channel.
set_burst_period	Set the internal burst period (seconds) on channel.
set_burst_trigger	Set the burst trigger source on channel.
set_modulation	Configures modulation.
set_offset	Set the DC offset (volts) on channel.
set_output_load	Set the output load impedance; None means high-Z.
set_sweep	Configure the sweep type on channel.
set_sweep_end_freq	Set the sweep end frequency (Hz) on channel.
set_sweep_return_time	Set the sweep return time (seconds) on channel.
set_sweep_start_freq	Set the sweep start frequency (Hz) on channel.
set_sweep_start_hold_time	Set the sweep start hold time (seconds) on channel.
set_sweep_stop_hold_time	The 33521B has no SWEep:HTIMe:STARt; HTIMe only holds at the stop frequency.
set_sweep_time	Set the sweep time (seconds) on channel.
set_sweep_trigger	Set the sweep trigger source on channel.
set_waveform	Program channel with the waveform definition.
sweep_enable	Enable or disable sweep mode on channel.